Get Latest [Oct-2021] Conduct effective penetration tests using TestPassed NS0-183
Penetration testers simulate NS0-183 exam PDF
NEW QUESTION 48
You have just finished installing and configuring an ONTAP cluster for a customer.
In this scenario, which product collects information and produces site documentation?
- A. Active IQ OneCollect
- B. Inventory Collect Tool
- C. SnapGathers
- D. NetAppDocs
Answer: D
NEW QUESTION 49
You are planning to install a new ONTAP 9.7 All SAN Array (ASA) into your existing data center.
In this scenario, which cluster configuration is allowed with ASA controllers?
- A. ASA controllers can only be added to clusters that have existing SAN licenses.
- B. ASA controllers can only be installed as a standalone HA pair.
- C. Add the ASA controllers to an existing 10-node cluster.
- D. Add the ASA controllers to an existing 4-node cluster with NAS licenses.
Answer: A
NEW QUESTION 50
Node 3 has taken over Node 4. You are attempting to access Node 4 on its management interface but cannot do it. In this scenario, how would you access Node 4's management interface?
- A. You must use the Service Processor; node management LIFS do not fall over between nodes.
- B. You should use SSH directly to one of the cluster interconnect switches; from there, you can use SSH to the node management on node 4.
- C. You have not waited long enough for the failover timeout for a node management LIF; there is a broadcast domain configured for this situation.
- D. Connect to the node management on Node 3 and then use the HA interconnect to access node 4.
Answer: A
NEW QUESTION 51
What are two ways to identify an AFF All SAN Array system? (Choose two.)
- A. View the ONTAP System Manager system nodes.
- B. View the ONTAP System Manager cluster settings.
- C. Use the san config show CLI command.
- D. Use the cluster image show CLI command.
Answer: A,C
Explanation:
Explanation
Ways to identify an ASA system You can identify an ASA system using ONTAP System Manager or using the ONTAP command line interface (CLI). From the ONTAP System Manager dashboard, you can click on the system nodes. The personality type is displayed as "ASA" for ASA systems. From the CLI, you can use san config show command. The ASA value returns as true for ASA systems
NEW QUESTION 52
In ONTAP 9.7 software, how many different replicated databases (RDBs) exist per node?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION 53
In an ONTAP switched cluster, which three types of traffic travels over the cluster network? (Choose three.)
- A. intercluster SnapMirror
- B. remote cluster peering
- C. cluster database replication
- D. intracluster SnapMirror
- E. Epsilon voting
Answer: A,B,C
NEW QUESTION 54
Click the Exhibit button.
You are setting up a new AFF A700 into a new rack at a customer's site. The customer asks you to plan for simplified future growth.
Referring to the exhibit, how would you satisfy this requirement?
- A. Option 3
- B. Option 1
- C. Option 2
- D. Option 4
Answer: C
NEW QUESTION 55
You finished a new installation and executed Config Advisor successfully. You review the physical racking and cabling on one of the controllers, and notice an amber light that was not previously on.
Which two actions should you perform before you turn over the cluster for production? (Choose two.)
- A. Review AutoSupport messages which could explain the controller state.
- B. Let the customer know the cluster is operating normally while the amber LED is on.
- C. Execute Config Advisor again to check for new errors.
- D. Remove cables connected to the controller until you find the one responsible for the controller issue.
Answer: A,C
NEW QUESTION 56
Click the Exhibit button.
You plan to install a new ONTAP cluster at a customer site by using the new ONTAP System Manager 9.7 GUI.
Referring to the exhibit, what must you do before you provision initial storage?
- A. Configure cluster LIFs.
- B. Configure aggregates.
- C. Configure protocols.
- D. Configure a remote tier.
Answer: B
NEW QUESTION 57
Click the Exhibit button.
You are installing a 2-node AFF A400 switchless cluster. You have cabled the management network to the e0M port. NetApp also recommends cabling to a redundant management network switch.
Referring to the exhibit, to which port should the redundant management network be cabled?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION 58
Which statement describes an SVM?
- A. An SVM is a logical device that shares data.
- B. An SVM is a node in the cluster.
- C. An SVM is a logical network interface.
- D. An SVM is a storage volume type.
Answer: A
NEW QUESTION 59
After completing the installation of a DS224C shelf, you observe the error shown in the exhibit.
Which action should you take to troubleshoot the error? (Choose two.)
- A. Re-seat the SAS card.
- B. Re-seat the IOM module.
- C. Perform a takeover-giveback.
- D. Reconnect the SAS cable.
Answer: B,D
NEW QUESTION 60
An ONTAP cluster is installed at a secure site. The array has no access to the Internet but is managed 24/7 by onsite engineers. The customer requires that when hardware failures occur, the failures are reported to the NetApp Support team as quickly as possible.
In this scenario, which two tasks should be performed during the project hand-off procedure to satisfy the customer's requirement? (Choose two.)
- A. Ensure that the onsite engineers receive EMS alerts when hardware issues occur.
- B. Educate the onsite engineer about how to manually log support calls.
- C. Ensure that Active IQ Config Advisor is installed.
- D. Educate the onsite engineers about invoking the AutoSupport tool from ONTAP System Manager.
Answer: A,D
NEW QUESTION 61
Click the Exhibit button.
You are adding new DS224C shelves in a new stack to your cluster with FAS8060 controllers running ONTAP 9.7.
Referring to the exhibit, which two actions should be performed to the cluster before installing the new shelves? (Choose two.)
- A. Move the SAS cables to a new stack.
- B. Disable out-of-band ACP.
- C. Remove the Ethernet cables.
- D. Enable in-band ACP.
Answer: A,B
Explanation:
Explanation/Reference:
NEW QUESTION 62
What are two ONTAP storage efficiency technologies that would be used on an AFF A400 cluster?
(Choose two.)
- A. FlexClone volumes
- B. FlashCache
- C. thin provisioning
- D. Flash Pool
Answer: B,D
NEW QUESTION 63
You just installed a new AFF A220 2-node cluster without additional disk shelves. When you review the Config Advisor output, you notice that your SAS cabling appears to be single-path HA.
In this scenario, which statement is true?
- A. AFF A220 controllers with internal disks support only single-path HA.
- B. Cable controller 1 0a to controller 2 0a, and cable controller 1 0b to controller 2 0b.
- C. The Config Advisor version you are using requires a plugin for AFF controllers.
- D. Cable controller 1 0a to controller 2 0b, and cable controller 1 0b to controller 2 0a.
Answer: D
NEW QUESTION 64
You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.5 on a customer site.
Referring to the exhibit, which steps are required to get an HA cabled system?
- A. 1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 4. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 4. 3. Cable the out-of-band ACP.
- B. 1. Insert a cable from right controller port 0a to IOMA port 1, and from port 0b to IOMB port 3. 2. Insert a cable from left controller port 0a to IOMB port 1, and from port 0b to IOMA port 3.
- C. 1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 3. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 3.
- D. 1. Insert a cable from right controller port 0a to IOMB port 1, and from port 0b to IOMA port 4. 2. Insert a cable from left controller port 0a to IOMA port 1, and from port 0b to IOMB port 4. 3. Cable the out-of-band ACP.
Answer: B
NEW QUESTION 65
What should you do to change the data protocol of a LIF?
- A. Add the new data protocol to the LIF.
- B. Shut down the assigned port.
- C. Delete and re-recreate the LIF.
- D. Put the LIF in another broadcast domain.
Answer: C
NEW QUESTION 66
After completing the installation of an AFF A800 ONTAP AI cluster, you are asked which contacts are available for additional help in obtaining immediate assistance in solving P1 issues.
In this scenario, what do you tell the customer?
- A. Contact NetApp Support using chat.
- B. Use Guided Problem Solving.
- C. Use the NetApp KB TV channel.
- D. Contact NetApp Support by telephone.
Answer: D
NEW QUESTION 67
......
Tested Material Used To NS0-183 Test Engine: https://www.testpassed.com/NS0-183-still-valid-exam.html